YB/T 4126-2023 高炉出铁沟浇注料/Blast furnace castable
高炉出铁沟浇注料
1范围
本文件规定了高炉出铁沟浇注料的术语和定义、牌号、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。
本文件适用于高炉主沟、铁沟、渣沟和摆动流槽等部位的工作层耐火浇注料(含预制件)，以及热修补用喷涂料。
2规范性引用文件
下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件;不注日期的引用文件，其最新版本(包括所有的修改单)适用于本文件。
GB/T 4513.2 不定形耐火材料 第2部分:取样
GB’T 4513.5 不定形耐火材料 第5部分:试样制备和预处理
GB/T 4513.6 不定形耐火材料 第6部分:物理性能的测定
GB/T 15545 不定形耐火材料包装、标志、运输、储存和质量证明书的一般规定
GB/T 16555 含碳、碳化硅、氮化物耐火材料化学分析方法
GB/T 18930 耐火材料术语
3术语和定义
GB/T 18930界定的术语和定义适用于本文件。
4 牌号
高炉出铁沟浇注料按高炉容积大小和使用部位分为ASC-1、ASC-2、ASC-3、ASC-4、ASC-5、ASC-6、ASC-7、ASC-8共八个牌号。其中A、S、C分别代表 Al2O3、SiC、C。
5技术要求
高炉出铁沟浇注料的理化指标应符合表1的规定。
|
表1高炉出铁沟浇注料的理化指标 |
||||||||||
|
项目 |
指 标 |
|||||||||
|
ASC-1 |
ASC-2 |
ASC-3 |
ASC-4 |
ASC-5 |
ASC-6 |
ASC-7 |
ASC-8 |
|||
|
w(Al2O3)% |
≥ |
70 |
55 |
65 |
60 |
55 |
55 |
60 |
55 |
|
|
w(SiC+F.C)/% |
≥ |
12 |
25 |
16 |
12 |
10 |
14 |
12 |
15 |
|
|
体积密度/(g/cm3) |
110℃X24 h |
≥ |
2.85 |
2.80 |
2.80 |
2.70 |
2.65 |
2.65 |
2.70 |
2.45 |
|
1450℃X3h(埋碳) |
≥ |
2.80 |
2.75 |
2.75 |
2.65 |
2.60 |
2.60 |
2.65 |
2.40 |
|
|
常温耐压强度/MPa |
110℃X24h |
≥ |
25 |
20 |
20 |
20 |
20 |
20 |
20 |
12 |
|
1450 ℃X3h(埋碳) |
≥ |
50 |
45 |
50 |
45 |
45 |
45 |
50 |
20 |
|
|
加热永久线变化/% |
1450℃X3h(埋碳) |
-0.1~0.5 |
-0.1~0.5 |
-0.1~0.5 |
-0.1~0.5 |
-0.1~ |
-0.1~0.5 |
-0.1~0.5 |
-0.5~0.5 |
|
|
推荐使用部位 |
≥2500m3高炉主沟铁 |
≥2500m高炉主沟渣线 |
1000m~2500 m3高炉主沟 |
<1000m3高炉主沟 |
铁沟 |
渣沟 |
摆动流槽 |
出铁沟热态修补 |
||
6试验方法
6.1试样制备按GB’T 4513.5进行，试样焙烧应在埋碳条件下进行。
6.2化学成分的测定按GB/T 16555进行。
6.3体积密度、常温耐压强度和加热永久线变化的测定按GB/T 4513.6进行。
7质量评定程序
7.1组批
产品按同一牌号组批，每批不大于60t，原料或生产工艺变更时应另行组批。
7.2抽样
产品抽样按GB/T 4513.2进行。
7.3合格判定规则
化学成分、常温耐压强度、加热永久线变化为验收检验项目。检验结果的平均值均符合表1的规定时，为合格。检验结果如有不合格项时，应按7.2重新取双倍数量的试样对不合格项进行复检。复检结果的平均值符合表1的规定，则判定该批次产品合格:否则判为不合格。
7.4合格评定形式
合格评定可采用供货方声明，使用方认定或第三方认证的形式进行。
8包装、标志、运输、储存及质量证明书
8.1包装、标志、运输和储存按GB/T 15545进行。
8.2产品发出时应附有质量证明书及使用说明书，质量证明书应载明供方名称、需方名称、生产日期、合同号、本文件编号、产品名称、牌号、批号、理化指标及保存期等内容。
Blast furnace castable
1 Range
This document specifies the terms and definitions, grades, technical requirements, test methods, quality assessment procedures, packaging, marking, transportation, storage and quality certificates of blast furnace castables.
This document is applicable to the working layer refractory castables (including prefabricated parts) in the main ditch, iron ditch, slag ditch and swing flume of blast furnace, as well as spray coatings for hot repair.
2 Normative reference documents
The contents of the following documents constitute the essential provisions of this document through normative references in the text. Where a reference file with a date is noted, only the version corresponding to that date applies to this file; Undated references, the latest version of which (including all change orders) applies to this document.
GB/T 4513.2 Amorphous refractories – Part 2: Sampling
GB’T 4513.5 amorphous refractories – Part 5: Sample preparation and preparation
GB/T 4513.6 Amorphous refractories – Part 6: Determination of physical properties
GB/T 15545 General requirements for packaging, marking, transport, storage and quality certificates of amorphous refractory materials
GB/T 16555 Method for chemical analysis of refractories containing carbon, silicon carbide and nitride
GB/T 18930 refractory terminology
3 Terms and definitions
The terms and definitions defined in GB/T 18930 apply to this document.
4 Brand
According to the volume of blast furnace and the use of the castable is divided into ASC-1, ASC-2, ASC-3, ASC-4, ASC-5, ASC-6, ASC-7, ASC-8 a total of eight grades. Where A, S and C represent Al2O3:, SiC and C respectively.
5 Technical Requirements
The physical and chemical indexes of castables in blast furnace casting ditch should conform to the provisions of Table 1.
|
Table 1. Physical and chemical indexes of castables in blast furnace castables |
||||||||||
|
Item |
Index |
|||||||||
|
ASC-1 |
ASC-2 |
ASC-3 |
ASC-4 |
ASC-5 |
ASC-6 |
ASC-7 |
ASC-8 |
|||
|
w(Al2O3)% |
≥ |
70 |
55 |
65 |
60 |
55 |
55 |
60 |
55 |
|
|
w(SiC+F.C)/% |
≥ |
12 |
25 |
16 |
12 |
10 |
14 |
12 |
15 |
|
|
Bulk density/(g/cm3) |
110℃X24 h |
≥ |
2.85 |
2.80 |
2.80 |
2.70 |
2.65 |
2.65 |
2.70 |
2.45 |
|
1450℃X3h(Carbon embedding) |
≥ |
2.80 |
2.75 |
2.75 |
2.65 |
2.60 |
2.60 |
2.65 |
2.40 |
|
|
Compressive strength at room temperature/MPa |
110℃X24h |
≥ |
25 |
20 |
20 |
20 |
20 |
20 |
20 |
12 |
|
1450 ℃X3h(Carbon embedding) |
≥ |
50 |
45 |
50 |
45 |
45 |
45 |
50 |
20 |
|
|
Heating permanent line change/% |
1450℃X3h(Carbon embedding) |
-0.1~0.5 |
-0.1~0.5 |
-0.1~0.5 |
-0.1~0.5 |
-0.1~ |
-0.1~0.5 |
-0.1~0.5 |
-0.5~0.5 |
|
|
Recommended parts |
≥2500m3Blast furnace main ditch iron line |
≥2500mBlast furnace main ditch slag line |
1000m~2500 m3Blast furnace main ditch |
<1000m3Blast furnace main ditch |
Iron furrow |
Slag channel |
Oscillating chute |
Hot repair of iron ditch |
||
6 Test methods
6.1 The sample preparation shall be carried out according to GB’T 4513.5, and the sample roasting shall be carried out under the condition of carbon burial.
6.2 The chemical composition was determined according to GB/T 16555.
6.3 The measurement of bulk density, compressive strength at room temperature and permanent line change of heating was carried out according to GB/T 4513.6.
7 Quality assessment procedures
7.1 Batch
The products shall be batch according to the same brand, each batch shall not be greater than 60t, and another batch shall be formed when the raw materials or production process is changed. 7.2 Sampling
Product sampling was conducted according to GB/T 4513.2.
7.3 Qualification Rules
Chemical composition, pressure strength at room temperature, heating permanent line changes are the acceptance inspection items. If the average values of the test results meet the requirements of Table 1, it is qualified. If there are any unqualified items in the test results, the unqualified items shall be reinspected by taking double the number of samples according to 7.2. If the average value of the reinspection results conforms to the provisions of Table 1, the batch of products is judged to be qualified: otherwise, it is judged to be unqualified.
7.4 Form of conformity assessment
The conformity assessment can be carried out in the form of the supplier’s declaration, the user’s certification or the third-party certification.
8 Packing, marking, transportation, storage and quality certificate
8.1 Packing, marking, transportation and storage shall be carried out in GB/T 15545.
8.2 The product shall be issued with a quality certificate and instruction manual. The quality certificate shall indicate the name of the supplier, the name of the demander, the date of production, the contract number, the number of this document, the name of the product, the brand number, the batch number, the physical and chemical index and the sh
